|
DETAILS |
| |
 Detailed
drawings
Installation
Type1
Installation
Type2
Disclaimer:
Thermalright or its owners or partners is not responsible
for damage or loss of any kind that may occur as
a result of using or misusing this or any product
we manufacture. Use common sense and review all
product details prior to use. Ask a question |
|
|
| STEP
1 |
STEP
2 |
| |
|
| Uninstall stock cooler by
removing the two screws circled in red. |
Then remove the 11 screws
(circled in red) from the back of the video card. |
| STEP
3 |
STEP
4 |
| |
|
| Remove stock cooler. |
Clean off the paste and
any residue for best contact and adhesiveness. |
| STEP
5 |
STEP
6 |
| |
|
| Insert the push pins though
the holes from the HSI heatsink indicated by the
red circles and apply thermal compound to the bottom
as well as on the HSI chipset and then stick it
on top of the HSI chipset. |
HR-03 Plus new version HSI
heat sink ,support 8800GTX & 8800 GTS video
card |
| STEP
7 |
STEP
8 |
| |
|
| Apply the include RAMsinks
to the 8 RAM chips shown in the above picture. |
Apply the “flat”
RAMsinks to the 4 RAM chips above the GPU shown
in the above picture. |
| STEP
9 |
STEP
10 |
| |
|
| Apply the PWM IC heatsinks
to the 4 PWM IC chips shown in the above picture. |
Apply the included square
padding to the center of the cross shaped backplate
to avoid any contact with component parts on the
video card. |
| STEP
11 |
STEP
12 |
|
|
| Screw in the 4 screws into
the holes on the mounting bracket. |
Spread a thin layer of thermal
compound evenly to the GPU and to the bottom of
the heatsink base. |
| STEP
13 |
STEP
14 |
|
|
| Place the heatsink
with the mounting bracket on top of GPU and with
the screws through the mounting holes. |
Insert the black washers
through the screws on the other side. |
| STEP
15 |
STEP
16 |
|
|
Insert
the backplate through the 4 screws with the square
padding in contact with the board. |
Screw in the screw cap through
the 4 screws. |
| STEP
17 |
STEP
18 |
|
|
| Type I installation complete. |
Insert each end of fan wire
clip into their designated holes (circled in red)
on the heatsink shown in the above picture. |
STEP
19 |
|
|
|
| Place a 92mm fan on top
of heatsink and pull on the fan wire clips to hook
into the fan mounting holes. |
|
| |
STEP
1 |
STEP
2 |
|
|
| Uninstall stock
cooler by removing the two screws circled in red. |
Then remove the 11 screws
(circled in red) from the back of the video card. |
STEP
3 |
STEP
4 |
|
|
| Remove stock cooler. |
Clean off the paste and
any residue for best contact and adhesiveness. |
STEP
5 |
STEP
6 |
|
|
| Insert the push pins though
the holes from the HSI heatsink indicated by the
red circles and apply thermal compound to the bottom
as well as on the HSI chipset and then stick it
on top of the HSI chipset. |
HR-03 Plus new version HSI
heat sink ,support 8800GTX & 8800 GTS video
card |
STEP
7 |
STEP
8 |
|
|
| Apply the include RAMsinks
to the 8 RAM chips shown in the above picture. |
Apply the “flat”
RAMsinks to the 4 RAM chips above the GPU shown
in the above picture. |
STEP
9 |
STEP
10 |
|
|
| Apply the PWM IC heatsinks
to the 4 PWM IC chips shown in the above picture. |
Apply the included square
padding to the center of the cross shaped backplate
to avoid any contact with component parts on the
video card. |
STEP
11 |
STEP
12 |
|
|
| Spread a thin layer of thermal
compound evenly to the GPU and to the top of the
heatsink base. |
Insert the screws through
the holes on the backplate and then insert black
washers through those 4 screws on the side where
the square padding is. |
STEP
13 |
STEP
14 |
|
|
| Apply the backplate to the
back of the video card with the 4 screws inserted
through the mounting holes. Please make sure that
the square padding is in between the card and the
backplate. |
Place the mounting bracket
on the heatsink from the other side and screws in
the screw caps to secure heatsink in place. |
STEP
15 |
STEP
16 |
|
|
| Type II installation complete. |
Insert each end of fan wire
clip into their designated holes (circled in red)
on the heatsink shown in the above picture. |
STEP
17 |
|
|
| Place a 92mm fan on top
of heatsink and pull on the fan wire clips to hook
into the fan mounting holes. |
| |
| |
| Installation
of 82mm, 70mm, 60mm fan |
STEP
1 |
STEP
12 |
 |
 |
Place the fan on top of
heatsink and insert zip tie through fin holes and
then back to mounting holes on the fan.
|
Pull zip tie to tighten
and secure fan to the heatsink. |
Installation
Guide
HR-03 Plus
